Jw at 08:53, 16 November 2015

2015-11-16T08:53:56Z

← Older revision		Revision as of 10:53, 16 November 2015
Line 91:		Line 91:
	:All output values are computed for the specified frequency range (or the corresponding octave range).		:All output values are computed for the specified frequency range (or the corresponding octave range).

	~~[[Category~~:~~Programmer Guide]]~~[[~~Category:SPU Reference~~]]		;See also:
			<[[../#Signal Processing Atoms\|SP-atoms]]>
			<!-- AN, 2.5.2011 -->

Jw: Jw moved page SPU Reference/ADSET1 to Programmer Guide/SPU Reference/ADSET1

2015-11-16T08:52:18Z

Jw moved page SPU Reference/ADSET1 to Programmer Guide/SPU Reference/ADSET1

← Older revision	Revision as of 10:52, 16 November 2015
(No difference)

Jw: Jw moved page SPU Reference/ADSET1 - compute global spectral descriptor data set 1 to SPU Reference/ADSET1 without leaving a redirect

2015-11-16T08:49:37Z

Jw moved page SPU Reference/ADSET1 - compute global spectral descriptor data set 1 to SPU Reference/ADSET1 without leaving a redirect

← Older revision	Revision as of 10:49, 16 November 2015
(No difference)

Admin: 1 revision: Initial import

2010-11-18T16:31:56Z

1 revision: Initial import

← Older revision	Revision as of 18:31, 18 November 2010
(No difference)

193.171.195.8: initial import

2010-05-17T13:05:27Z

initial import

New page

{{DISPLAYTITLE:{{SUBPAGENAME}}}}
====ADSET1 - compute global spectral descriptor data set #1====

Compute global spectral descriptor data set #1.

To each of the input spectra A0 to AN-1 the following processing is applied:

*The hearing threshold is applied to the input spectrum <var>A</var> (if input <var>HTH</var> is set to <code>1</code>) and the frequency range is truncated to the selected range (<var>FMIN</var>, <var>FMAX</var>). The following spectral descriptors are computed from the linear spectrum:

*Energy (rms)

*Flux: the 1st order flux is computed, which is the correlation coefficient of two spectra. To compute a higher order flux the correlations must be multiplied.

*The amplitude spectrum is converted to dB (<var>AREF</var> -> 0dB) and the following spectral descriptors are computed from the logarithmic spectrum:

*Deviation: the standard deviation of the logarithmic amplitudes

*Smoothness: the sum of the differences of each log. spectral amplitude ai to the local average around ai.

*The value <var>AFLOOR</var> is subtracted from the logarithmic spectrum and all values of the resulting spectrum which are lower than zero are truncated (set to zero). The following spectral descriptors are computed from the shifted and truncated spectrum:

*Centroid and spread

*Linear spectral slope and octave-scale spectral slope: for both values the slope of the linear regression is used. For the linear slope the x-values are the frequencies in Hertz and for the octave slope the x-values are (relative) frequencies in octaves.

This SPAtom was developed for the NOIDESc project in 2006.

=====Usage:=====

<code>ADSET1 <var>N</var> <var>A</var> <var>AREF</var> <var>HTH</var> <var>DF</var> <var>FMIN</var> <var>FMAX</var> <var>AFLOOR</var></code>

=====Inputs:=====

;<var>N</var>

:The number output vectors (frames).

;<var>A</var>

:The FFT amplitude spectrum (linear).

;<var>AREF</var>

:The reference amplitude (linear).

;<var>HTH</var>

:Hearing threshold. The following values are supported:

:<code>0</code> - dont' apply
<code>1</code> - apply

;<var>DF</var>

:The FFT resolution in Hz.

;<var>FMIN,FMAX</var>

:The analysis frequency range in Hz.

;<var>AFLOOR</var>

:The amplitude floor for Fct/Fsp in dB. Note that <var>AFLOOR</var> is only used for the computation of Fct and Fsp.

=====Outputs:=====

;<var>RES1</var>

:RES1[*,0] - rms energy in dB (Arms)

:RES1[*,1] - spectral centroid frequency in Hz (Fct)

:RES1[*,2] - normalized spectral spread (no unit) (Fsp)

:RES1[*,3] - spectral slope in dB / oct. (Osl)

:RES1[*,4] - spectral flux (no unit) (Sfx)

:RES1[*,5] - spectral smoothness in dB (Ssm)

:RES1[*,6] - amplitude variance in dB (Avar)

:RES1[*,7] - spectral slope in dB / kHz (Fsl)

:All output values are computed for the specified frequency range (or the corresponding octave range).

[[Category:Programmer Guide]][[Category:SPU Reference]]

Programmer Guide/SPU Reference/ADSET1 - Revision history

Jw at 08:53, 16 November 2015

Jw: Jw moved page SPU Reference/ADSET1 to Programmer Guide/SPU Reference/ADSET1

Jw: Jw moved page SPU Reference/ADSET1 - compute global spectral descriptor data set 1 to SPU Reference/ADSET1 without leaving a redirect

Admin: 1 revision: Initial import

193.171.195.8: initial import